The autumn leaves have begun to fall. Winter is coming. And that means it's time to start preparing your motorhome for hibernation if you plan on parking it for a long period of time. Winterizing is one of the most important parts of ensuring that your coach runs smoothly for many years to come.
“Customers need to winterize their motorhomes in frigid weather to keep water from freezing and damaging the expensive parts in their plumbing system," said D. Ray Hester, the Tiffin Service Center Shop Manager. “When pipes freeze and expand, then thaw out, tiny leaks or cracks can occur, which could ultimately cause water damage to the interior of the motorhome." Here's the detailed checklist you need to be sure you don't forget an important step in winterizing your motorhome. Before you get started, be sure to have these items on hand:
- 1-1/16-inch wrench or socket and ratchet
- Water Pressure Regulator Valve
- RV Antifreeze
- Standard half-inch hose to connect to the inlet side of the water pump
- Teflon tape
Get a Hose. Find An Open Lot. And Prepare to Drain Outside
- Empty both grey water and black water holding tanks by pulling each lever and allowing them to flow out of the back of the coach. Be sure you are in a location where it's easy to wash the remnants away with a hose or bucket.
- By walking around the outside rear of the coach, remove and drain the fresh water tanks by flipping the switch, then turn it back off.
- Also on the outside of the coach, locate the service panel containing your water lines. Drain the hot and cold water lines, then shut them off.
- Release the pressure from the water tank filter and remove by unscrewing it from the base. Once the filter is out and water is drained from the canister, reinstall it.
- Drain the hot water heater by removing the service panel cover. Be sure the tank is switched off. You can also turn off the hot water heater breaker to kill power to the water heater outside. Relieve the pressure, and remove the plug, which will require a 1-1/16-inch wrench. It's common for the anode rod to be rotted, so be prepared if you need to replace it. From there, allow water to run free.
- And finally, locate the outside service panel containing the refrigerator water line. The hose should be hanging from the top just outside of the panel. Drain the fridge water from the outside of the coach by using a wrench to loosen the bolt on the end of the line and turning the water on to allow the remaining water to run out.
But Wait, There's More To Drain
- Now that you've emptied all the tanks and outside lines, it's time to test all faucets to check both hot and cold water is no longer flowing.
- Drain toilets, then flush.
- Go to the shower and test that hot and cold water has drained.
- Run the washing machine and dishwasher to ensure they are also drained.
- And finally, return to the outside service panel containing your city water fill. This is usually the same outside panel containing the grey and black tanks. Have a regulator on hand that is pre-set between 40-50 pounds of air. Anything more could cause damage to faucets and lines. Hook your regulator up to the city water fill and connect it to the water heater. Water will run free.
- Then, wrap Teflon tape around the base of the anode rod and install it into the water heater. Start by turning it by hand before using your wrench to avoid cross-threading. Tighten the rod back up with a wrench and reinstall the protective plate.
Don't Forget to Drain the Refrigerator
- To drain the water dispenser of the refrigerator, one person will need to be inside at the fridge to press the water dispenser down, and one person will need to be outside to hook up the air hose to the water line. Once the hose is pushing air through, all remaining water will run free from the water dispenser, so be ready with a large cup.
- Next, remove the water filter out of the fridge.
- Install a plug (which came with your coach) where the filter was located, and close it up.
- Now you can reconnect the water line to the fridge, and turn the valve back to an open position.
Last steps: Add Antifreeze
- To be able to safely add antifreeze to each water source throughout the coach, first, bypass the water heater. Do this by turning the lever to “bypass" so that antifreeze will not run through the water heater. This is a very important step.
- Now attach your common air hose to the city water gauge, so that air pressure will run through all your appliances' water lines. Return inside to flush out all cold and cold water from faucets by letting them run dry.
- Go back outside and take the pressure you have connected to the city water gauge back off.
- Install the antifreeze via the inlet side of the water pump, usually identifiable by the clear plastic screen. Do so by disconnecting the inlet side and attaching a half-inch clear hose, then place it into the antifreeze. This hose comes with standard packages in a Tiffin motorhome, but you can also purchase it at your local hardware store or from the Tiffin parts department.
- Turn on the water pump, and turn the faucet back on. You will see the antifreeze run through the faucet by turning on both hot and cold water. The same applies to the dishwasher and washing machine. Don't forget about the outside faucet or shower.
- Leave faucets open, meaning, leave them in a position as if they would be running. The antifreeze will eventually run dry.
- Pour antifreeze into all sink drains and clean off remnants from the sink bowl. Then pour it into toilets, allowing it to remain there for the season. Repeat the same with your showers.
- Then pour it into toilets, allowing it to remain there for the season.
- Repeat the same with your showers.
NOTE: It's important to remember that there are many types of motorhomes, and because of that, these steps may vary from brand to brand. This checklist was based on a Tiffin motorhome.